Lorixen.
EN

Google Ads location targeting: stop paying for far-off clicks

Short answer: Google Ads defaults to "Presence or interest", which means people who have only shown interest in your suburb or city can see your ads from somewhere else entirely. If you only serve people who are physically in your area, switch the campaign's location option to "Presence", target the suburbs or postcodes you actually cover (or a sensible radius), add exclusions for the gaps, and then check the Matched locations report every couple of weeks. Google says plainly that location targeting is a best effort, so expect a little leakage even with everything set correctly.

A plumber in Geelong does not want to pay for a click from someone in Perth who searched "plumber Geelong" for their mum. A mobile dog wash in western Sydney does not want calls from the Central Coast. Both usually trace back to a few settings, none of which needs a new campaign.

Symptom → cause → fix

Start with what you are seeing, then match it to the likely setting.

What you notice Likely cause Fix
Calls or forms from people interstate Location option left on the default "Presence or interest" Change to "Presence" in campaign settings (Locations → Location options)
Clicks from the next city over Target is a whole city or region when you only serve part of it Replace the city with suburbs, postcodes or a radius you really travel to
Ads showing in a pocket you skip (across a river, a toll road, a long drive) Radius covers areas you don't want Keep the radius, add those suburbs or postcodes as exclusions
Report shows lots of "Unspecified" Google could not place the person from IP address or query, or the search was on Maps over a large area Normal to a degree; judge by trend, not single rows
Spend looks fine but leads are poor in one area Area is targeted correctly, it just converts badly Lower the bid there (manual bidding) or remove the area
Bid changes by location "don't work" Campaign uses Smart Bidding, which doesn't support manual bid adjustments Accept the automated bids or change the area itself, not the bid

The rest of this article walks through the settings in the order you'd fix them.

Walk-through: the settings that decide where you show

1. Choose Presence or Presence or interest

Google's advanced location options page describes two choices for who gets included:

  • Presence or interest (the default and the one Google recommends): people who are likely to be in, or regularly in, your targeted locations, plus people who have shown interest in those locations through their searches, recent visits or the content they view.
  • Presence: people who are likely to be in, or regularly in, your targeted locations.

Google also notes that most campaigns see fewer impressions after switching away from the default. That is the point for a local service business: you want fewer, nearer people. The interest option makes more sense for tourism, accommodation or anything people book from elsewhere, such as a Margaret River winery or a Byron Bay surf school.

Exclusions work on Presence: by default they exclude people likely to be located in the excluded area, and people outside it may still see your ads.

These options apply to Search, Display and Demand Gen campaigns. Google states that Demand Gen keeps presence and interest together as its default and recommended setting.

2. Pick the shape of your area

Google lets you target countries, areas within a country and a radius around a point. Depending on the country, "areas within a country" can mean regions, cities or postal codes. Type your area into the location search and the results show what types it accepts.

Which shape to use:

  • Radius: good for a business with one base and a travel limit, like a mobile mechanic who covers "about 25 km". Google's minimum radius is 1 km.
  • Suburbs or postcodes: better when your real area is lopsided, for example you go north along the coast but not inland. A list of postcodes copied from your own job history is often the most honest map you have.
  • Whole city or state: only when you really do serve all of it.

You can add locations one by one, or in bulk. Google's bulk tool accepts up to 1,000 locations at a time, which is handy if you work from a postcode list.

3. Fill the gaps with exclusions

Exclusions are not just for other countries. Use them inside your area: the far side of a bridge you won't cross at peak hour, a pocket of suburbs with access trouble, an island you don't ferry to. Google's exclusion guide shows excluded locations with a red outline when you select "Show locations on map", which is the fastest way to sanity-check a postcode list.

One rule from Google: the number of locations you exclude shouldn't exceed the number you target in a campaign. If you find yourself excluding more than you include, rebuild the target list instead.

4. Read the Matched locations report

This is where you find out what really happened. In Google Ads, go to Campaigns → Insights & reports → When and where your ads showed, then open the Matched locations tab. Google says these locations could be people's physical locations or locations of interest, so if you've just switched to Presence, compare a period after the change with one before it.

The Targeted locations view shows performance per location you chose. The Matched view shows where ads actually matched. If you use location assets, a Distance report (Report editor → Predefined reports → Locations → Distance) shows performance by distance to your nearest business location.

Two cautions from Google's own help: metrics below country level may not add up to campaign totals, because some impressions are only matched at country level, and "Unspecified" rows appear when neither the IP address nor the search showed a recognisable location.

5. Adjust bids only where they still apply

Location bid adjustments range from −90% to +900% at campaign level. They are useful with manual bidding: raise bids in the suburbs closest to you, lower them at the edges. But Google states that if you use Smart Bidding strategies such as Target CPA, Target ROAS, Maximize conversions or Maximize conversion value, manual bid adjustments aren't supported. For most small accounts on automated bidding, the location list and exclusions are the levers that count.

A note on Performance Max

Performance Max campaigns show across many surfaces at once, so it is worth checking their Locations section separately rather than assuming it copies your Search campaign. Google's API notes say exclusions in Performance Max, like Search, Display and Shopping, use Presence; you can't set them to presence-or-interest. When a Performance Max campaign is sending you distant leads, the Matched locations report is still where to look first.

FAQ

Why does Google still show my ad to a few people outside the area?

Google states that location targeting is a best effort based on signals such as settings, devices and behaviour, and that it can't guarantee 100% accuracy. A small amount of leakage is expected. A steady stream from one far-away area points to a setting worth checking.

Should every local business use Presence?

Most businesses that travel to customers or need customers to walk in should. If people regularly book you from somewhere else, such as visitors planning a holiday, keep the interest option and judge it by leads, not impressions.

Is a radius or a postcode list better?

A radius is quicker to set and fine for even, round service areas. Postcodes or suburbs suit areas shaped by roads, rivers or your own travel habits. You can combine them: a radius plus exclusions does the job for many tradies.

How long before I can tell whether the change worked?

There's no fixed period. Wait until the Matched locations report has a meaningful number of clicks after the change (a small budget takes longer), then compare it with an equal stretch of time before the change.

Where your enquiry form or call tracking can't tell you which suburb a lead came from, we can help connect the ad settings to the leads you actually get.

Sources

WhatsAppLet’s talk